1039A

1039A

Back to Main Genelec Page

Pricing Sheet

Genelec 1039A is a very powerful main monitor for large control rooms. It is designed for flush mounting in the control room wall. It can also be used free standing.

Separate signal conditioning & power amplifier module in a 7U 19" equipment rack is not shown in the picture.

•Frequency response 29 - 20k Hz (-3 dB)
•126 dB peak SPL @ 2m per pair with music material
•Two long throw 385 mm (15") woofers
•130 mm (5") high sensitivity midrange cone driver
•25 mm (1") high frequency metal dome driver
•Directivity Control Waveguide™ (DCW™) provides excellent stereo imaging and frequency balance even in difficult acoustic situations
•320 litre vented cabinet
•Powerful final amplifiers 2x400 W, 350 W, 120 W
•Electronic crossover and protection circuitry
•Built-in bass, mid and treble level controls, bass and treble roll-off and bass tilt controls
•The 1039A is a TEC (Technical Excellence & Creativity) award winner.

See 1039A studio application examples from: Counterpoint Studios, Darkhorse Recording Studios, Engine Studios

Retail $18,500 CAD (Each)

Our Price $11,375 US (Each)

Our Price $17,500 CAD (Each)

Order Form

System Specifications

Lower cut-off frequency, -3 dB:	< 29 Hz
Upper cut-off frequency, -3 dB:	> 20 kHz
Free field frequency response of system:	31 Hz - 20 kHz (± 2.5 dB)
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz: @ 1m	> 126 dB SPL
Maximum long term RMS acoustic output in same conditions with IEC-weighted noise (limited by driver unit protection circuit): @ 1m	> 120 dB SPL
Maximum peak acoustic output per pair @ 2 m from the engineer with music material:	> 126 dB
Self generated noise level in free field @ 2m on axis:	< 15 dBA
Harmonic distortion at 100 dB SPL @ 1m on axis: 50...200 Hz 200...10 kHz	< 1% < 0.5%
Drivers: Bass Mid Treble	2 x 385 mm (15") cone 1 x 130 mm (5") cone 1 x 25 mm (1") metal dome
Weight: Speaker Amplifier	115 kg (253 lb) 30 kg (66 lb)
Speaker dimensions (Horizontal mounting): Height Width Depth	820 mm (32 1/4") 1050 mm (41 3/8") 550 mm (21 5/8")
Amplifier dimensions: Height Width Depth	310 mm (12 3/16") 483 mm (19") 250 mm (9 13/16")

Amplifiers

Bass amplifier output power with an 8 Ohm load:	Short term 2 x 400 W
Mid amplifier output power with a 8 Ohm load:	Short term 350 W
Treble amplifier output power with an 8 Ohm load:	Short term 120 W
Long term output power is limited by driver unit protection circuitry.
Slew rate:	80 V/µs
Amplifier system distortion at nominal output:	THD < 0.05% SMPTE-IM < 0.05% CCIF-IM < 0.05% DIM 100 < 0.05%
Signal to Noise ratio, referred to full output:	Bass > 100 dB Mid > 100 dB Treble > 100 dB
Mains voltage:	100/200V or 115/230V
Voltage operating range at 230V setting: 115V setting:	207 - 244 V (-10/+6 %) 104 - 122 V (-10/+6 %)
Power consumption:	Idle 70 W Full output 1000 W

Crossover

Input connector: XLR female	pin 1 gnd pin 2 + pin 3 -
Input impedance:	10 kOhm balanced
Input level for 100 dB SPL output @ 1m:	variable from +6 to -6 dBu
Input level for maximum short term output of 126 dB SPL @ 1m:	variable from +32 to +20 dBu
Subsonic filter below 25 Hz :	18 dB/octave
Ultrasonic filter above 22 kHz:	12 dB/octave
Crossover frequencies:	Bass/Mid 400 Hz Mid/Treble 3.2 kHz
Crossover acoustical slopes:	> 24 dB/octave
Level control operating range in 1 dB steps:	Bass from 0 to -6 dB Mid from 0 to -6 dB Treble from 0 to -6 dB
Bass roll-off control in 2 dB steps:	from 0 to -8 dB @ 29 Hz
Bass tilt control in 2 dB steps:	from 0 to -8 dB @ 50 Hz
The 'CAL' position is with all tone controls set to 'off' and input sensitivity control to maximum and corresponds to a maximally flat free field response.