1037B

•Frequency response: 35 - 22k Hz (-3 dB)
•122 dB SPL (peak) per pair @ 2 m with music  material
•300 mm (12") woofer
•130 mm (5!) high sensitivity direct radiating cone driver •Loaded with a Directivity Control Waveguide™  (DCW™)
•25 mm (1") metal dome tweeter with proprietary DCW
•65 litre vented cabinet
•Tri-amplified: 180 W, 120 W, 120 W
•Electronic crossover and protection circuitry
•Built in bass, mid and treble level controls,  bass roll  off and tilt controls
•Rack mount adaptors available for soffit installations

The 1037B is designed for use as a main monitor in moderate sized control rooms for music, surround sound monitoring or CD mastering, and in television and general purpose broadcasting studios, cutting rooms and drama studios. It performs well both free standing and flush mounted in the wall.

See 1037B studio application examples from: AudioArt Recording Studio, Producers Video

THX ® pm3 certified

THX and Lucasfilm are (C) Lucasfilm Ltd. & TM. All rights are reserved. Used under authorization.

Retail $6,999 CAD (Each)
Our Price $3,981 US (Each)
Our Price $6,125 CAD (Each)

System Specifications
Lower cut-off frequency, -3 dB: < 35 Hz
Upper cut-off frequency, -3 dB: > 22 kHz
Free field frequency response of system: 37 Hz - 21 kHz (± 2.5 dB)
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz: @ 1 m > 116 dB SPL
Maximum long term RMS acoustic output in same conditions with IEC-weighted noise (limited by driver unit protection circuit): @ 1m > 107 dB SPL
Maximum peak acoustic output per pair on top of console, @ 1.7m from the engineer with music material: > 126 dB
Self generated noise level in free field @ 1m on axis: < 15 dB (A-weighted)
Harmonic distortion at 95 dB SPL at 1m on axis:
freq. <100 Hz
freq. >100 Hz
< 3%
< 0.5%
Drivers:
Bass
Mid
Treble
305mm (12") cone
130 mm (5") cone
25mm (1") metal dome
Weight: 37 kg (82 lb)
Dimensions:
Height
Width
Depth
680mm (26 3/4")
400mm (15 3/4")
380mm (15")
Amplifier
Bass amplifier output power with a 8 Ohm load: Short term 180W
Midrange amplifier output power with a 8 Ohm load: Short term 120W
Treble amplifier output power with a 8 Ohm load: Short term 120W
Long term output power is limited by driver unit protection circuitry. Slew rate : 80V/micros
Amplifier system distortion at nominal output: THD < 0.05%
SMPTE-IM < 0.05%
CCIF-IM < 0.05%
DIM 100 < 0.05%
Signal to Noise ratio, referred to full output: Bass > 100 dB
Midrange > 100 dB
Treble > 100 dB
Mains voltage: 100/200V or 115/230V
Voltage operating range at 230V setting: 207 - 253V (± 10%)
Power consumption: Idle 50W
Full output 300W
Crossover
Input connector: XLR female pin1 gnd
pin2 +
pin3 -
Input impedance: 10 kOhm
Input level for 100 dB SPL output @1m: variable from +6 to -6 dBu
Input level for maximum short term output of 116 dB SPL @1m: variable from +22 to +10 dBu
Subsonic filter below 32 Hz : 18 dB/octave
Ultrasonic filter above 25 kHz: 12 dB/octave
Crossover frequency: Bass/Mid 420 Hz
Mid/Treble 3.2 kHz
Crossover acoustical slopes: 18 - 24 dB/octave
Crossover level control operating range in 1 dB steps: Bass from 0 to -6 dB
Mid from 0 to -6 dB
Treble from 0 to -6 dB
Bass roll-off control in 2 dB steps: from 0 to -8 dB @35 Hz
Bass tilt control in 2 dB steps: from 0 to -8 dB @80 Hz
The 'CAL' position is with all tone controls set to 'off' and the volume control to maximum (fully clockwise).


©2000-2002 Canada Promedia Inc. and Shahin Al Rashid Website Design. All rights reserved.