1036A

The 1036A is an extremely powerful main monitor for large control rooms. 1036A is designed for top performance installations where you do not want to compromise the low distortion reproduction at any audible frequency, and where the loudspeaker is flush mounted in the wall of the control room.

The separate signal conditioning & power amplifier unit is not shown in the picture.

•Frequency response: 19 - 22k Hz (-3 dB)
•136 dB SPL (peak) per pair @ 2m with music material
•Two long throw 460mm (18") woofers
•Two 130 mm (5") high sensitivity direct radiating cone drivers loaded with a Directivity Control  Waveguide™ (DCW™)
•25 mm (1") throat compression tweeter driver with a Directivity Control Waveguide™ (DCW™)
•430 litre vented cabinet
•Tri-amplified: 2 x 1100W, 600W, 300W
•Electronic crossover and protection circuitry
•Built-in bass, mid and treble level controls, bass and treble tilt and bass roll-off controls

The 1036A is a TEC (Techical Excellence ∓ Creativity) and SSAIRA (Studio Sound Audio Industry Recognition Award) winner.

Retail $44,000 CAD (Each)
Our Price $26,918 US (Each)
Our Price $41,412 CAD (Each)

System Specifications
Lower cut-off frequency
-3 dB
-6 dB Lower cut-off frequency
-3dB
-6dB
< 19 Hz
< 17.5 Hz
Upper cut-off frequency, -3 dB: > 22 kHz
Free field frequency response of system: 21 Hz - 20 kHz (± 2.5dB)
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz @ 1m > 131dB SPL
Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver unit protection): @ 1m > 126dB SPL
Maximum peak acoustic output per pair
@ 2m from the engineer with music material:		 > 136dB SPL
Self generated noise level in free field @ 2m on axis: < 20dB (A-weighted)
Harmonic distortion at 100dB SPL @ 1m on axis:
50...200Hz
200Hz...4kHz
>4kHz		 < 1%
< 0.5%
< 3%
Drivers:
bass
mid
treble

 2x 460mm (18") cone
2 x 130mm (5") cone,
25mm (1")
compression driver
Weight (speaker/amplifier): 182 kg (401 lb) / 71 kg (156 lb)
Dimensions speaker:
Height
Width
Depth		 960mm (37 3/4")
1180 mm (46 1/2")
650mm (25 1/2")
Dimensions amplifier:
Height
Width
Depth		 755mm (29 3/4")
483mm (19")
370mm (14 9/16")
Note that cable connectors require additional 100mm (4") of space behind both amplifier and speaker.
Amplifier
Bass amplifier output power with an 8 Ohm load:
Long term output power is limited by driver unit protection circuitry. 		Short term 2 x 1100W
Mid amplifier output power with a 4 Ohm load:
Long term output power is limited by driver unit protection circuitry. 		Short term 600W
Treble amplifier output power with an 8 Ohm load:
Long term output power is limited by driver unit protection circuitry.		 Short term 300W
Slew rate: 100V/micros
Amplifier system distortion at nominal output: THD < 0.05%
SMPTE-IM < 0.05%
CCIF-IM< 0.05%
DIM 100 < 0.05%
Signal to Noise ratio, referred to full output: Bass > 101dB
Mid > 105dB
Treble > 106dB
Mains voltage: 100/110/115/220/230/240V
Voltage operating range: 230V setting: 219...241V ±5%
115V setting: 109...121V ±5%
Power consumption: Idle 150VA
Full output 3500VA
Crossover
Inputs  XLR female balanced 10 kOhm
Input level for 110dBSPL @1m output: variable from +15 to -5dBu
Input level for maximum short term output of 131dB SPL @1m: variable +36 to +16dBu
Subsonic filter below 18Hz: 18 dB/octave
Ultrasonic filter above 22kHz: 12 dB/octave
Crossover frequency, Bass/Mid/ and Mid/Treble: 400Hz, 3.5kHz
Crossover acoustical slopes: > 24dB/octave
Level control operating range in 1dB steps -- bass, mid and treble: 0...-6dB and mute
Bass roll-off control in 2 dB steps: 0...-8dB @30Hz
Bass tilt control operating range in 2dB steps: 0...-8dB @50Hz
The 'CAL' position is with all tone controls set to 'off' and the volume control to maximum (fully clockwise).

©2000-2002 Canada Promedia Inc. and Shahin Al Rashid Website Design. All rights reserved.