1035B

1035B

Back to Main Genelec Page

Pricing Sheet

This extremely powerful main monitor for large control rooms is required when very high levels and wide bandwidth reproduction are essential. 1035B is designed for top performance installations where the loudspeaker is flush mounted in the wall of the control room.

The separate 19" rack mountable signal conditioning & power amplifier unit is not shown in the picture.

•Frequency response 29 - 20k Hz (-3 dB)
•136 dB SPL (peak) per pair @ 2m with music material
•Two long throw 385 mm (15") woofers
•Two 130 mm (5") high sensitivity direct radiating cone drivers loaded with a Directivity Control Waveguide™ (DCW™)
•25 mm (1") throat compression driver with a Directivity Control Waveguide™ (DCW™)
•380 litre dual chamber vented cabinet
•Tri-amplified: 2 x 1100 W, 600 W, 300 W
•Electronic crossover and protection circuitry
•Built-in bass, mid and treble level controls, bass and treble roll-off and bass tilt controls

See 1035B studio application examples from: Circle House, Extasy, Sony Tree, 20th Century Fox.

Retail $38,500 CAD (Each)

Our Price $23,706 US (Each)

Our Price $36,471 CAD (Each)

Order Form

System Specifications

Lower cutoff frequency, 3dB:	< 29 Hz
Upper cutoff frequency, 3dB:	> 22 kHz
Free field frequency response of system:	31 Hz - 20 kHz (± 2.5 dB)
Maximum short term sine wave acoustic output on axis in half space averaged from 100Hz to 3KHz @ 1m	> 131 dB SPL
Maximum long term RMS acoustic power in same conditions with IEC-weighted noise: @ 1m	> 126 dB SPL
Maximum peak acoustic output per pair at engineers site, speakers @ 2 m from the engineer, with music material:	> 136 dB
A -20 dBu signal input will produce 107 dB SPL in free field @ 1 m on axis with the controls at the 'CAL' position. The 'CAL' setting is with all crossover control switches set to the 'off' position and the sensitivity set to maximum. See specification in the Crossover Section.
Self generated noise level in free field @ 2m on axis:	< 20 dBA
Harmonic distortion at 100 dB SPL @ 1 m on axis: 50..200 Hz 200Hz..4 kHz > 4 kHz	< 1 % < 0.5 % < 3 %
Drivers: Bass: Mid Treble	2 x 385 mm (15") cone 2 x 130 mm (5") cone 25 mm (1") compression
Weight: speaker amplifier	142 kg (313 lb) 71 kg (156 lb)
Speaker dimensions (Horizontal mounting): Height Width Depth	820 mm (32 1/4") 1105 mm (43 1/2") 775 mm (30 1/2")
Amplifier dimensions: Height Width Depth	755 mm (29 3/4") 483 mm (19") 370 mm (14 9/16")

Amplifier

Bass amplifier output power an 8 ohm load:	Short term 2 x 1100 W
Mid amplifier output power a 4 ohm load:	Short term 600 W
Treble amplifier output power an 8 ohm load:	Short term 300 W
Continuous output power is limited by the driver unit protection processor.
Slew rate:	100 V/µs
Amplifier system distortion at nominal output:	THD < 0.05 % SMTEIM < 0.05 % CCIFIM < 0.05 % DIM100 < 0.05 %
Signal to noise ratio, at amplifier outputs with shorted signal input:	bass > 101 dB midrange > 105 dB treble > 106 dB
Mains voltage:	100/110/115/200/220/230/240 VAC
Voltage operation range:	± 5 %
Power consumption:	Idle 150 VA Full output 3500 VA

Crossover

Input connector: XLR female	pin 1 gnd pin 2 + pin 3 -
Input impedance:	10 kohm balanced
Input level for 110dB SPL output @ 1m:	variable from +15 to -5 dBu
Input level for maximum short term output of 131 dB SPL @ 1m:	variable from +36 to +16 dBu
Subsonic filter below 27 Hz:	18 dB/octave
Ultrasonic filter above 22 kHZ:	12 dB/octave
Crossover frequencies:	bass/midrange 400 Hz midrange/treble 3.5 kHz
Level control operation range in 1 dB steps:	bass from 0 to -6 dB & MUTE mid from 0 to -6 dB & MUTE treble from 0 to -6 dB & MUTE
Bass roll-off filter in 2 dB step:	from 0 to -8 dB @ 30 Hz
Bass tilt control in 2 dB steps:	from 0 to -8 dB @ 50 Hz
15 kHz roll-off control in 1 dB steps:	from +1 to -3 dB @15kHz
The 'CAL' setting is with all crossover control switches set to the 'off' position and the sensitivity set to maximum and corresponds to a maximally flat free field response.