| 1032A |
 |
Frequency response:
40 - 22k Hz (-3 dB) |
|
The 1032A is aimed at the needs of high power nearfield monitoring, broadcast monitoring, TV control rooms, mobile vans, CD mastering, smaller project and home studios. It's high performance and compact size allow it to be used with compact digital workstations.
THX and Lucasfilm are (C) Lucasfilm Ltd. & TM. All rights are reserved. Used under authorization. |
THX
® pm3 certified|
Retail
$3,799 CAD (Each)
|
Our
Price $2,113 US (Each)
|
Our
Price $3,250 CAD (Each)
|
| System Specifications | |
| Lower cut-off frequency, -3 dB: | < 40 Hz |
| Upper cut-off frequency, -3 dB: | > 22 kHz |
| Free field frequency response of system: | 42 Hz - 21 kHz |
| Maximum short term sine wave acoustic
output on axis in half space, averaged from 100 Hz to 3 kHz: @1m @0.5 m |
> 113
dB SPL > 119 dB SPL |
| Maximum long term RMS acoustic output
in same conditions with IEC-weighted noise (limited by driver unit protection
circuit): @1m @0.5 m |
> 103
dB SPL > 109 dB SPL |
| Maximum peak acoustic output per pair on top of console, @ 1m from the engineer with music material: | > 124 dB |
| Self generated noise level in free field @ 1m on axis: | |
| Harmonic distortion at 95 dB SPL at 1m
on axis: freq. 50Hz...100 Hz >100 Hz |
< 1% < 0.5% |
| Drivers Bass: Treble: |
250mm (10")
cone 25mm (1") metal dome |
| Weight: | 48 Ib. (21,7 kg) |
| Dimensions Height: Width: Depth: |
495mm (19
1/2") 320mm (12 5/8") 290mm (11 1/3") |
| Amplifier | |
| Bass amplifier output power with an 4 Ohm load: | 180 W |
| Treble amplifier output power with an
8 Ohm load: Long term output power is limited by driver unit protection circuitry. |
120 W |
| Slew rate: | 80V/micros |
| Amplifier system distortion at nominal output: | THD < 0.05% SMPTE-IM < 0.05% CCIF-IM < 0.05% DIM 100 < 0.05% |
| Signal to Noise ratio, referred to full output: | Bass > 100 dB Treble > 100 dB |
| Mains voltage: | 100/200V or 115/230V |
| Voltage operating range at 230V setting: 115V setting: |
207 - 253
V (± 10%) 104 - 126V (± 10%) |
| Power consumption: | Idle 50 W Full output 200 W |
| Crossover | |
| Input connector: XLR female | pin1 gnd pin2 + pin3 - |
| Input impedance: | 10 kOhm balanced |
| Input level for 100 dB SPL output @1m: | variable from +6 to -6 dBu |
| Input level for maximum short term output of 113 dB SPL @1m: | variable from +19 to +7 dBu |
| Subsonic filter below 40 Hz : | 18 dB/octave |
| Ultrasonic filter above 25 kHz: | 12 dB/octave |
| Crossover frequency: | 1.8 kHz |
| Crossover acoustical slopes: | 24 - 32 dB/octave |
| Treble tilt control operating range in 2dB steps: | from+2 to -4dB & MUTE |
| Bass roll-off control in 2 dB steps: | from 0 to -8 dB @ 40 Hz |
| Bass tilt control in 2 dB steps: | from 0 to -6 dB &MUTE |
| The 'CAL' position is with all tone controls set to 'off' and the volume control to maximum (fully clockwise). | |
©2000-2002 Canada Promedia Inc. and Shahin Al Rashid Website Design. All rights reserved.
